Skip to content
Maintenance

How to Flush a Water Heater: Step-by-Step Guide

Flushing is the single best thing you can do for a tank water heater in hard-water country. Here's how to do it safely.

By Covina Water Heater Pros · · 2 min read

How to Flush a Water Heater: Step-by-Step Guide

Quick answer

To flush a water heater: turn off the gas or power, close the cold-water supply valve, attach a garden hose to the drain valve and run it outside, open a hot water tap to relieve pressure, then open the drain valve and let the tank empty. Briefly open the cold supply to stir up remaining sediment, repeat until the water runs clear, then close the drain, refill the tank and restore power or relight the pilot.

Need it fixed today? Call (626) ***-****

Before You Start

  • Garden hose long enough to reach outside or a floor drain
  • Flathead screwdriver (some drain valves need one)
  • Bucket and towels
  • Gloves
  • About an hour

Safety first: Tank water is hot. Either let it cool for a few hours with the heater off, or be very careful with the discharge.

Step by Step

  1. Turn off the heat. Gas: set the control knob to OFF or PILOT. Electric: switch off the breaker. Never heat an empty electric tank, as it will burn out the elements.
  2. Close the cold-water supply valve on top of the heater.
  3. Attach a hose to the drain valve at the bottom and run it to a safe drain spot.
  4. Open a hot tap somewhere in the house to let air in.
  5. Open the drain valve and let the tank drain completely.
  6. Stir it up: with the drain open, open the cold supply for a few seconds to push out remaining sediment. Repeat until the water runs clear.
  7. Close the drain valve, remove the hose, and open the cold supply to refill.
  8. Wait until water flows steadily from the open hot tap, then close it.
  9. Restore heat: turn on the breaker or relight the pilot / set the gas control back to your setting.

Not sure what's wrong with your water heater?

Talk to a local Covina technician now. Honest advice, upfront pricing.

(626) ***-****

Troubleshooting

The drain valve is clogged

Hardened sediment can block the valve. Try opening and closing the cold supply a few times to push water back through. If it's still clogged, a pro can use a special flushing tool or replace the valve with a full-port brass one.

The drain valve won't close or drips

Plastic drain valves often leak after being opened for the first time in years. Cap it with a hose cap for now and have it replaced.

Water heater makes more noise after flushing

Loose sediment may have moved around. Flushing again usually helps. If it doesn't, the sediment may have hardened into scale.

How Often?

In Covina, once a year is a good rule. Large households may benefit from every six months. If your tank is 5+ years old and has never been flushed, consider having a professional do the first one to avoid a stuck or broken valve.

Want a full checklist? Our Covina maintenance guide covers flushing, anode rods, T&P valves and more.

This article is general information for Covina-area homeowners. Gas, venting and electrical work should be done by a licensed professional. For help with your specific water heater, call (626) ***-****.

Frequently Asked Questions

About 30–60 minutes for draining and flushing, plus reheating time of 30–60 minutes for gas or longer for electric.
Sometimes. On very old tanks, sediment can be plugging small leaks. Flushing can also cause old plastic drain valves to drip. This is a reason to have older tanks flushed by a pro.
Tankless units are descaled rather than drained. See our tankless descaling guide.

Rather Have a Pro Flush It?

Annual water heater flushes and tune-ups across Covina.

Call (626) ***-****
Call Now Free Quote